Archive for Cisco

CCNA 3.1 Semester 1 Final Exam Result Correct 100% (Option 1)

{ January 27, 2010 @ 11:32 PM } · { Cisco, Networking }
{ Tags: } · { Comments (1) }

1. Which devices will create multiple collision domains in an Ethernet network? (Choose two.)
Switch router
… continue reading this entry.

CCNA 2 – Module 2 Exam Answers V4.0

{ October 9, 2009 @ 4:30 PM } · { Cisco }
{ Comments (1) }

1. A static route that points to the next hop IP will have what administrative distance and metric in the routing table?
• administrative distance of 0 and metric of 0
• administrative distance of 0 and metric of 1
• administrative distance of 1 and metric of 0
• administrative distance of 1 and metric of 1
… continue reading this entry.

CCNA 2 – Module 1 Exam Answers V4.0

{ October 9, 2009 @ 4:29 PM } · { Cisco }
{ Leave a Comment }

1. If a router cannot find a valid configuration file during the startup sequence, what will occur?
• The startup sequence will reset.
• The router will prompt the user for a response to enter setup mode.
• The startup sequence will halt until a valid configuration file is acquired.
• The router will generate a default configuration file based on the last valid configuration.
• The router will monitor local traffic to determine routing protocol configuration requirements.
… continue reading this entry.

CCNA 1 – Final Exam Answers V4.0

{ October 9, 2009 @ 4:27 PM } · { Cisco }
{ Comments (5) }

1. Refer to the exhibit. Host B attempts to establish a TCP/IP session with host C. During this attempt, a frame was captured at the FastEthernet interface fa0/1 of the San Francisco router. The packet inside the captured frame has the source IP address 10.10.1.2, and the destination IP address is 10.31.1.20. What is the destination MAC address of the frame at the time of capture?
• 0060.7320.D632
• 0060.7320.D631
• 0040.8517.44C3
• 0009.B2E4.EE03
• 0010.C2B4.3421
… continue reading this entry.

CCNA 1 – Module 11 Exam Answers V4.0

{ October 9, 2009 @ 4:26 PM } · { Cisco }
{ Leave a Comment }

1. Users in the network are experiencing slow response time when doing file transfers to a remote server. What command could be issued to determine if the router has experienced any input or output errors?
• show running-config
• show startup-config
• show interfaces
• show ip route
• show version
• show memory
… continue reading this entry.

CCNA 1 – Module 10 Exam Answers V4.0

{ October 9, 2009 @ 4:25 PM } · { Cisco }
{ Comments (1) }

1. Refer to the exhibit. A student working in the lab selects a cable that is wired as shown. Which connection types can successfully be made with this cable? (Choose two.)
• connecting a PC to a router’s console port
• connecting two routers together via their fast ethernet ports
• connecting two switches together at gigabit speeds
• connecting a PC to a switch at Gigabit Ethernet speeds
• connecting two devices with the same interface type at Fast Ethernet spee

CCNA 1 – Module 9 Exam Answers V4.0

{ October 9, 2009 @ 4:23 PM } · { Cisco }
{ Leave a Comment }

1. In the graphic, Host A has reached 50% completion in sending a 1 KB Ethernet frame to Host D when Host B wishes to transmit its own frame to Host C. What must Host B do?
• Host B can transmit immediately since it is connected on its own cable segment.
• Host B must wait to receive a CSMA transmission from the hub, to signal its turn.
• Host B must send a request signal to Host A by transmitting an interframe gap.
• Host B must wait until it is certain that Host A has completed sending its frame.
… continue reading this entry.

« Previous entries